Dynamic

Compatible with Dynamic Indoor Rowers (manufactured from November 2010–present). Click here to view Schematic Diagram.

Dynamic There are 19 products.

Showing 1 - 19 of 19 items
  • $270.00

    Our most advanced Performance Monitor. Features wireless heart rate monitoring, the ability to store workouts to a USB flash drive (sold separately), and is backlit for improved visibility in low light environments. See more info.

    $270.00
  • $30.00

    Replacement handle for the Model D, E and Dynamic Indoor Rowers. Overmolded grips made of soft rubber won´t absorb sweat, grease or dirt. Does not include U-bolt nuts. See more info.

    $30.00
  • $23.00

    For use on all Concept2 Indoor Rowers. Replacement seat top. 12" wide, 10" deep, 1½" thick, with contours for pelvic bones and tailbone. Mounting screws and lock washers (four each) included. Original equipment on Model C, D, E and Dynamic Indoor Rowers. Can be retrofitted on all Model B and most Model A Indoor Rowers, replacing the original "kidney"...

    $23.00
  • $22.00

    For use with Model C, D, E and Dynamic Indoor Rowers. One of the 3-1/4 inch wide top seat rollers (two per machine; sold individually) that runs on the stainless steel track on the monorail. Mounting hardware that holds the roller on the seat frame is not included, because it can usually be re-used. If you need the hardware, order part number 1728...

    $22.00
  • $9.50

    For use with updated Model D, Model E and Dynamic Indoor Rowers. Also fits Model C and original Model D Indoor Rowers but is dark gray in color. This flexfoot piece fits into the footstretcher covers (part numbers 1054 and 1055, sold separately) to make the complete footstretcher assembly. Footplate/Flexfoot Assembly Diagram

    $9.50
  • $7.00

    For use with Model C, D, E and Dynamic Indoor Rowers. This is one of the small bottom seat rollers (two per machine; sold individually) that runs under the top edge of the monorail. Does not include the mounting hardware (nut, bolt and spacers) that hold the roller on the seat frame, because it can usually be reused. If you need the hardware, order part...

    $7.00
  • $7.00

    For use with Model A, B, updated D and E Indoor Rowers. This is the left caster wheel for the front foot.

    $7.00
  • $7.00

    For use with Model A, B, updated D and E Indoor rowers. This is the right caster wheel for the front foot.

    $7.00
  • $5.61

    For use with the updated Model D, Model E and Dynamic Indoor Rowers. Left footstretcher cover. The flextfoot piece (part number (part number 1063, sold separately) fits into this part to make the complete footstretcher assembly. Footplate/Flexfoot Assembly Diagram This item is out of stock until mid-April.

    $5.61
  • $5.61

    For use with the updated Model D, Model E and Dynamic Indoor Rowers. Right footstretcher cover. The flextfoot piece (part number (part number 1063, sold separately) fits into this part to make the complete footstretcher assembly. Footplate/Flexfoot Assembly Diagram

    $5.61
  • $4.75

    For use with updated Model D, Model E and Dynamic Indoor Rowers.  Replacement nylon footstrap with buckle, approximately 30" long by 1" wide with a screwhole drilled approximately 9" from the buckle end. Two per machine. Sold individually. Model D/E Flexfoot Assembly Diagram

    $4.75
  • $3.50

    For use on all Model B, C, D, E and Dynamic Indoor Rowers. This is the R8 bearing located outside of the flywheel. The corresponding bearing cup (part number 1013) is sold separately. See more info.

    $3.50
  • $3.00

    For use with Model A, B, C, D and E Indoor Rowers. This is the hard plastic cap that goes on the rear metal legs of the indoor rower to protect your carpet or floor and keep the machine from sliding back and forth while you row. Two per machine. Sold individually.

    $3.00
  • $0.70

    For use on all Model C, D, E and Dynamic Indoor Rowers as well as all SkiErgs. This is the rubber bearing cup that holds the R8 bearing on indoor rowers (part number 232, sold separately) and the 12mm bearing on SkiErgs. See more info.

    $0.70
  • $0.50

    For use on all Model C, D, E and Dynamic Indoor Rowers. This is the 5/8 inch long spacer found in the return mechanism's travelling pulley. Also used in the monitor arm assembly on the Dynamic Indoor Rower.

    $0.50
  • $0.00

    For use with Model D, E and Dynamic Indoor Rowers with manufacture dates from March 13, 2015–August 27, 2015. If the foot belly screws on your machine are loosening with use, this reinforcement kit will remedy the problem. Kit contains two triangular braces that reduce flexing of the foot belly, and 14 new style screws that are less prone to loosening.

    $0.00
Showing 1 - 19 of 19 items