No products
Prices are tax included
Parts listed here are compatible with Model Ds manufactured from July 14, 2003–July 21, 2006 (serial numbers 071403–072106).
This is the part of the indoor rower that connects to the Performance Monitor on one end and the chain guide brackets on the other. For use on all Model C and Model D Indoor Rowers. See more info.
For use with the Model C, D and E Indoor Rowers. This is the 2" x 2" x 3/4" metal traveling pulley assembly with a chain idler pulley included. The chain and shock cord come together at the traveling pulley, and the traveling pulley moves back and forth inside the indoor rower on every stroke. One per machine. See more info.
This tube houses the 5-1/2 inch bolt that holds the monorail hangar assembly together. For use on all Model C Indoor Rowers and on Model D Indoor Rowers manufactured from July 2003–2006. Order two per machine.
For use on the Model C, D and E Indoor Rower. This is the part that the chain passes through before entering into the flywheel assembly. See more info.
T27 6-Lobe driver required to turn the front leg fasteners (part number 2952) on Model C, D (original and updated) and E Indoor Rowers.
For use with updated Model D, Model E and Dynamic Indoor Rowers. Replacement nylon footstrap with buckle, approximately 30" long by 1" wide with a screwhole drilled approximately 9" from the buckle end. Two per machine. Sold individually. Model D/E Flexfoot Assembly Diagram For machine manufactured after July 31, 2006.
For use with Model A, B, C and original D Indoor Rowers. Replacement nylon footstrap with buckle, approximately 24" long by 1" wide with a screwhole drilled approximately 7" from the buckle end. Two per machine. Sold individually. For machines manufactured prior to July 31, 2006.
For use with Model C, D and E Indoor Rowers. This is a 3-3/8 inch diameter pulley that the shock cord (part number 1731) runs over inside the Concept2 Indoor Rower. There are four per machine. Sold individually. See more info.
For use with Model C, D, E and Dynamic Indoor Rowers. This is one of the small bottom seat rollers (two per machine; sold individually) that runs under the top edge of the monorail. Does not include the mounting hardware (nut, bolt and spacers) that hold the roller on the seat frame, because it can usually be reused. If you need the hardware, order part...
For use on all Model C, D and E Indoor Rowers. This is the 17mm bearing located outside of the flywheel. The corresponding bearing cup (part number 1012) is sold separately. See more info.
For use with Model C and original Model D Indoor Rowers. Replacement caster wheel located on the front foot of Model C and original Model D Indoor Rowers. Used when picking up the back end of the indoor rower and rolling it like a wheel barrow.
For use on all Model C, D, E, and Dynamic Indoor Rowers and the SkiErg. Using this knob instead of a nut makes it easier to take the monitor on and off of the equipment.
For use on the Model C, D and E Indoor Rower. This is the end cap for the front of the indoor rower. See more info.
For use on the Model C, D and E Indoor Rower.
For use on all Model B, C, D, E and Dynamic Indoor Rowers. This is the R8 bearing located outside of the flywheel. The corresponding bearing cup (part number 1013) is sold separately. See more info.
For use with Model C, D and E Indoor Rowers. These are the 1¼" diameter urethane pulleys that the chain runs over inside the indoor rower. There are two per machine: one is part of the traveling pulley (part number 1756); the other is mounted on a stationary axle and has two chain idler spacers (part number 1305) to keep it properly aligned. See more info.
For use with Model A, B, C, D and E Indoor Rowers. This is the hard plastic cap that goes on the rear metal legs of the indoor rower to protect your carpet or floor and keep the machine from sliding back and forth while you row. Two per machine. Sold individually.
For use on all Model C Indoor Rowers and on Model D Indoor Rowers manufactured from July 2003–2006.
For use with Model C, D and E Indoor Rowers. This is the handle hook used on the Models C, D and E Indoor Rower. To store the handle long-term, place the handle up against the flywheel housing. For ease of use before or during a workout, placing the handle in the handle hook puts the handle within easy reach. Includes hardware.